|
Specification |
Colors (If Applicable) |
Description |
|
A-423-66 |
Fed-STD-595C |
One type of two-component epoxy based finish coat for the
aerospace industry. This product is specifically formulated
for industrial aerospace use on metals. |
|
A-932-66 |
#17178 Aluminum |
A two-component aluminized epoxy enamel. |
|
A-A-8 |
N/A |
Shellac. |
|
A-A-208B |
Fed-STD-595C |
A marking ink. |
|
A-A-344 |
Clear gloss |
An interior and exterior lacquer. |
|
A-A-665D |
Fed-STD-595C |
An aerosol nitrocellulose lacquer. |
|
A-A-665E |
Fed-STD-595C |
An aerosol fast-dry alkyd enamel. |
|
A-A-857B |
N/A |
A thinner for reducing the viscosity of cellulose- nitrate
based dopes and lacquers of the spraying type. Suitable for
use under air pollution regulations. |
|
A-A-1452B |
#17038 Black #17875 White |
An acid, gasoline and oil resistant lacquer formulated for
spraying the aluminum surface around storage batteries. -
Type I: #17038 Gloss Black - Type II: #17875 Gloss White |
|
A-A-1546A |
Fed-STD-595C |
A rubbing varnish. |
|
A-A-1558A |
Fed-STD-595C |
A high opacity, solvent base coating for use in marking
bales, crates, boxes and drums. |
|
A-A-1572 |
Clear |
A lacquer type sanding sealer for spray application. For use
on interior wood to be topcoated with clear lacquer
finishes. May be applied by conventional or airless spray
equipment. Can be used in conjunction with a stain, washcoat
and/or a filler together with lacquer finish coats. |
|
A-A-1788 |
Fed-STD-595C |
An oilbase interior varnish. |
|
A-A-1800 |
Fed-STD-595C |
An oilbase spar varnish. |
|
A-A-2246B |
Fed-STD-595C |
A ready mixed, flat gloss, latex-based paint for use on
interior walls and ceilings. |
|
A-A-2335 |
Clear |
A varnish-type surface sealer for wood and cork floors. |
|
A-A-2336 |
White |
An oilbase/alkyd wood primer for interior and exterior
surfaces. |
|
A-A-2787 |
Fed-STD-595C |
A solvent thinned, low VOC, aerosol enamel. |
|
A-A-2850 |
Fed-STD-595C |
A waterborne polymeric coating compound. |
|
A-A-2886A |
Black Green Yellow Red blue |
A ready-mixed traffic paint for application to traffic
bearing surfaces, such as Portland cement, concrete,
bituminous pavement, brick surfaces of streets, highways,
bridges, tunnels, etc. - Type I: Standard dry - Type II:
Fast dry |
|
A-A-2904 |
N/A |
A mineral spirit, regular and odorless, for use as a
solvent, cleaner or thinner with coatings such as alkyd
paints, alkyd primers, composed of natural or synthetic
resin vehicles. - Type I: Conventional - Type II: High flash
point - Type III: Odorless |
|
A-A-2962A |
Fed-STD-595C |
An exterior grade, semi-gloss alkyd enamel formulated for
low VOC" content. - Type I: Lusterless - Type II: Semigloss
- Type III: Gloss - Class A: 340 g/l max VOC - Class B: 420
g/l max VOC " |
|
A-A-2994 |
Fed-STD-595C |
A primer coating for interior walls/wood. |
|
A-A-3003 |
Fed-STD-595C |
A very high quality nitrocellulose lacquer for general
interior use as a finishing coat over a properly prepared
primed metal, plastic or sealed wood substrates. |
|
A-A-3054 |
Black |
A heat-resisting paint. |
|
A-A-3058 |
Fed-STD-595C |
An interior fire-retardant paint. |
|
A-A-3120 |
Fed-STD-595C |
A swimming pool paint. - Class A: Acrylic base - Class C:
Chlorinated rubber base - Class E: Epoxy base |
|
A-A-3121 |
Fed-STD-595C |
A high quality, chlorinated rubber deck enamel for concrete
and masonry surfaces. This product is extremely durable and
provides a chemical resistant surface. This is a
single-component coating, no catalyst required. |
|
A-A-3161 |
Fed-STD-595C |
A coating primer conditioner for chalking exterior surfaces. |
|
A-A-3164 |
Fed-STD-595C |
A low VOC, lusterless and semigloss synthetic resin lacquer
for application onto a lacquer resistant primer or recoating
properly prepared metal surfaces. |
|
A-A-3165 |
Fed-STD-595C |
A durable, pigmented, high gloss lead and chromate free
lacquer for spray or brush application. It has good exterior
durability and gloss. |
|
A-A-3183 |
Fed-STD-595C |
A latex exterior paint. |
|
A-A-50574 |
Fed-STD-595C |
A high quality odorless semigloss alkyd enamel for use on
all interior wood, metal or masonry surfaces. This product
is extremely durable with excellent flow and leveling
characteristics. |
|
A-A-59166 |
Fed-STD-595C |
A non-slip walkway coating for the exterior of aircraft
surfaces. - Type I: Smooth, no grit - Type II: Grit added |
|
A-A-59281 |
N/A |
A cleaning compound of solvent mixtures. - Type I: Normal
blend - Type II: Non-photochemically reactive blend |
|
AMS-3170 |
N/A |
One type of specially blended solvent specially formulated
for the reduction of Graphite Varnish Coating. |
|
ASTM-D-740 |
N/A |
Shellac. |
|
C-252-66 |
N/A |
A gloss epoxy type catalyst is an amine based air dry
catalyst designed specifically for two component epoxy
coatings. |
|
C-1178-66 |
N/A |
C-1178-66 type converter is an amine based catalyst designed
specifically for two component epoxy coatings. Such films
show excellent chemical, solvent and corrosion resistance as
well as hardness and toughness. |
|
DOD-E-1115C |
White |
An interior/exterior alkyd enamel. |
|
DOD-E-24607A |
Fed-STD-595C (Semigloss only) |
A government specification, non-flaming enamel. |
|
DOD-P-15328D |
Green |
A two-component metal pretreatment wash primer. |
|
MIL-A-6091 |
N/A |
A specification denatured alcohol solvent. |
|
MIL-C-450C |
Black |
A bituminous, asphalt solvent type coating for application
on the interior surfaces of ammunition items such as bombs,
shells, rockets, and mines prior to being filled with
explosives. - Type I: 15 - 28 seconds #4 Ford Cup viscosity
- Type II: 120 - 190 seconds #4 Ford Cup viscosity - Type
III: 150 - 250 seconds #4 Ford Cup viscosity |
|
MIL-C-8514C |
Yellow |
A metal pretreatment wash primer. |
|
MIL-C-17504B |
Clear |
A single component, clear acrylic plastic coating for use as
a protective coating. Formulated for the protection and
sealing of substrates. Provides resistance to water,
sunlight, chemicals and abrasion. Available in bulk liquid
form and in aerosol cans. |
|
MIL-C-22750D |
Fed-STD-595C |
A two-component epoxy-polyamide coating for spray and brush
applications, furnished in a packaged kit and suitable for
use under air pollution regulations. Formulated for the
protection against solvents and chemicals on interior and
exterior surfaces. - Type I: Standard formulation - Type II:
Low infrared reflection formulation |
|
MIL-C-22750F |
Fed-STD-595C |
A two-component, hi-solids, low-VOC, epoxy-polyamide coating
for spray and brush applications, furnished in a packaged
kit and suitable for use under air pollution regulations.
Formulated for the protection against solvents and chemicals
on interior and exterior surfaces. |
|
MIL-C-38736B |
N/A |
A cleaning compound of solvent mixtures. - Type I: Normal
blend - Type II: Non-photochemically reactive blend |
|
MIL-C-46168D |
Fed-STD-595C |
A two-component, hi-solids aliphatic, CARC polyurethane
coating. |
|
MIL-C-53039B |
Fed-STD-595C |
A single component, hi-solids aliphatic, CARC polyurethane
coating. |
|
MIL-C-81773C |
Fed-STD-595C |
A two-component polyurethane coating. |
|
MIL-C-83231A |
Black White |
A rain erosion-resistant polyurethane coating. |
|
MIL-C-83286B |
Fed-STD-595C |
A two-component, isocyanate/polyester polyurethane coating
formulated for excellent exterior durability and gloss
retention. |
|
MIL-C-83445A |
White |
A rain erosion-resistant, non-yellowing white polyurethane
coating. |
|
MIL-C-85285C |
Fed-STD-595C |
A two-component aliphatic, polyester polyurethane coating. |
|
MIL-DTL-15090D |
#26307 Light Gray |
A light gray equipment enamel for use as a topcoat on
equipment, furniture and electrical equipment such as
switchboard installations. |
|
MIL-DTL-24441C |
#26270 Haze Gray |
A two component epoxy polyamide paint designed to protect
surfaces from environmental attack. This coating is Low VOC
as well as lead and chromate free. |
|
MIL-DTL-24631 |
#37038 Black |
An exterior grade polyester urethane paint. - Type I: Epoxy
- Type II: Polyurethane |
|
MIL-DTL-53039C |
Fed-STD-595C |
A single component, hi-solids aliphatic, CARC polyurethane
coating. All types
available. |
|
MIL-E-5558A |
Fed-STD-595C |
A bake dry, alkyd base, wrinkle finish enamel. |
|
MIL-E-7729B |
Fed-STD-595C |
A high grade, single component, air dry, high gloss alkyd
enamel formulated for interior and exterior primed metal and
wood surfaces. |
|
MIL-E-11195E |
Fed-STD-595C (Lusterless only) |
A fast drying, lusterless, low VOC alkyd enamel. |
|
MIL-E-15090C |
#16307 Gray #26307 Gray |
A general purpose enamel with good durability for use on
steel furniture, machinery and equipment aboard ships or at
naval installations. - Type I: Medium air dry - Type II:
Fast air dry - Type III: Baking - Class 1: Gloss #16307 Gray
- Class 2: Semigloss #26307 Gray |
|
MIL-E-15145E |
Fed-STD-595C |
A zinc dust pigmented enamel. |
|
MIL-E-16663A |
Fed-STD-595C |
A rapid, air-drying and baking type enamels for production
line application by brushing, spraying, or dipping. For use
on metal surfaces of ammunition and ammunition containers. -
Type I: Air dry - Type II: Baking - Class 1: Rapid drying -
Class 2: Flash drying |
|
MIL-E-19603C |
Fed-STD-595C |
A baking enamel for roller coat application. |
|
MIL-E-22118B |
Red |
A synthetic insulating enamel for use on electrical
equipment and for general purpose use. |
|
MIL-E-24635B |
Fed-STD-595C |
An air-dry, silicone enamel conforming to MIL-E-24635B. It
is highly weather resistant with excellent color and gloss
retention. |
|
MIL-E-24763A |
Fed-STD-595C |
An emulsion type enamel. |
|
MIL-E-46096C |
Fed-STD-595C |
A lusterless, quick-dry, styrenated alkyd-type enamel. |
|
MIL-E-52798A |
Fed-STD-595C |
A camouflage alkyd enamel. |
|
MIL-E-52891B |
Fed-STD-595C |
A zinc phosphate type quick-dry lusterless enamel used as a
finishing topcoat on primed ammunition components and other
metal substrates. |
|
MIL-I-46058 |
Fed-STD-595C |
An electrical insulating compound. |
|
MIL-L-296B |
Purple |
A lacquer. |
|
MIL-L-6805 |
Fed-STD-595C (Gloss only) |
A nitro-cellulose lacquer. |
|
MIL-L-7178 |
Fed-STD-595C (Gloss only) |
A nitro-cellulose lacquer. |
|
MIL-L-10287B |
Fed-STD-595C |
A cellulose nitrate lacquer used in both the manufacture of
small arms ammunition for identification purpose and in the
assembly of small arms ammunition primers. - Type I: Opaque
- Type II: Semi-transparent |
|
MIL-L-11195D |
Fed Std. 595B |
A lusterless hot spray lacquer. |
|
MIL-L-19537C |
Fed-STD-595C (Gloss only) |
A general purpose exterior protective coating for metal
surfaces. It is particularly formulated for resistance to
diester lubricating oil, and is primarily intended for spray
application. |
|
MIL-L-19538C |
Fed-STD-595C |
A nitrocellulose camouflage lacquer for metal surfaces,
particularly formulated for resistance to diester
lubricating oil, and is primarily intended for spray
application. |
|
MIL-L-46159A |
Fed-STD-595C |
A low reflective acrylic lacquer for aircraft suitable for
use under air pollution regulations. It is intended to
provide a nonspecular surface for aircraft. - Type I: Spray
application - Type II: Aerosol cans |
|
MIL-L-52043C |
12 Fed-STD-595C |
A cellulose nitrate semigloss lacquer which can be applied
at either elevated or room temperatures. It is intended for
use as a finish coat on chemically treated and/or primed
tanks, trucks, automotive components and fire control
systems. |
|
MIL-L-81352A |
Fed-STD-595C |
An exterior acrylic lacquer for protection of metal
surfaces. - Type I: Acrylic - Type II: Alkyd - Type III:
Polyurethane |
|
MIL-L-81352B |
Fed-STD-595C |
An exterior acrylic lacquer for protection of metal
surfaces. - Type I: Acrylic - Type II: Alkyd - Type III:
Polyurethane |
|
MIL-P-8585A |
Green Yellow |
A low-moisture sensitivity, corrosion-inhibiting zinc
chromate primer. |
|
MIL-P-14105D |
Fed-STD-595C |
A heat-resisting paint intended for use on steel that
provides excellent protection. |
|
MIL-P-15328D |
Blue |
A metal pretreatment wash primer. |
|
MIL-P-19602B |
Fed-STD-595C |
A size-coating baking primer. |
|
MIL-P-21035B |
Gray |
A two part, high zinc dust content, galvanizing repair
compound. Provides cathodic protection similar to
galvanizing. - Type I: Rule 102 compliant - Type II: 295 g/l
max VOC |
|
MIL-P-21563B |
Clear Fluor. Red-Orange Fluor. Yellow-Orange |
A high visibility, durable, exterior, fluorescent paint
system including a clear overlay coating containing UV and
weather stabilizer which is sold separate from the pigmented
fluorescent base coat. |
|
MIL-P-21600A |
Clear Fluor. Red-Orange Fluor. Yellow-Orange |
A high visibility, durable, exterior, fluorescent paint
system including a clear overlay coating containing UV and
weather stabilizer which is sold separate from the pigmented
fluorescent base coat. |
|
MIL-P-22332B |
Red Oxide |
A corrosion-inhibiting, zinc chromate primer primarily
intended for coating the interior and exterior surfaces of
ammunition and rockets. |
|
MIL-P-23377F |
Yellow Dark Green |
A two-component, low VOC, high build, strontium chromate
type epoxy-polyamide primer for spray and brush
applications. Chemical- and solvent-resistant. - Type I,
Class C: Yellow - Type II, Class C: Dark Green |
|
MIL-P-23377G |
Yellow Dark Green |
A two-component, low VOC, high build, strontium chromate
type epoxy-polyamide primer for spray and brush
applications. - Type I, Class C: Yellow - Type II, Class C:
Dark Green |
|
MIL-P-24441A |
Green |
A heavy duty two component epoxy primer that does not
contain lead, chromium or other toxic metal pigments. - Type
I: |
|
MIL-P-26915B |
Gray |
A lead-free, high-solids zinc-dust primer for steel
surfaces. |
|
MIL-P-46105 |
Gray |
A single package, heat convertible/curing epoxy-based,
zinc-rich primer for use on ferrous metal surfaces prior to
spot welding. Protects steel galvanically, thus preventing
below film corrosion. |
|
MIL-P-47115 |
Fed-STD-595C |
An abrasion-, chemical-, and heat-resistant epoxy paint. |
|
MIL-P-52192B |
Red Oxide |
A two-component, air-drying or baking, chemical resistant
epoxy primer. Can be used for ferrous and non ferrous metals
as well as other substrates. |
|
MIL-P-53022A |
Fed-STD-595C |
A lead and chromate free, corrosion-inhibiting, epoxy
coating primer. |
|
MIL-P-53022B |
White Light Gray |
A two-component, flash dry, corrosion inhibiting lead and
chromate-free epoxy primer. Can be used for ferrous and
non-ferrous metals as well as other substrates. This primer
has a low Volatile Organic Compound(VOC) content and can be
used to replace MIL-P-23377F and MIL-P-52192 where exposure
to lead or chromate pigments is not acceptable. |
|
MIL-P-53030A |
White Gray |
A two component, air dry, water reducible epoxy type primer
for ferrous and non-ferrous metals. |
|
MIL-P-85582C |
#34151 Green #34052 Green |
A two-component waterborne epoxy polyamine primer. - Type I:
Standard #34151 Green - Type II: Low infrared reflective
#34052 Green - Class C2: Chromate rust inhibitor formulation
- Class N: Non-chromate rust inhibitor formulation |
|
MIL-P-85582D |
#34151 Green #34052 Green |
A two-component, waterborne hi-solids epoxy primer. - Type
I: Standard #34151 Green - Type II: Low infrared reflective
#34052 Green - Class C2: Chromate rust inhibitor formulation
- Class N: Non-chromate rust inhibitor formulation |
|
MIL-PRF-680 |
N/A |
A degreasing solvent. |
|
MIL-PRF-3043C |
Green (Blue in
package) |
A thermosetting resin coating for surfaces of engine
components and metal parts. Dyed to a semi- transparent blue
color which changes to green upon proper baking. |
|
MIL-PRF-22750F |
Fed-STD-595C |
A high-solids epoxy coating. |
|
MIL-PRF-23377G |
Yellow Dark Green |
A two-component, low VOC, epoxy-polyamide primer for spray
and brush applications. - Type I, Class C: Yellow - Type II,
Class C: Dark Green |
|
MIL-PRF-23377H |
Gray Yellow Dark Green |
A two-component, low VOC, epoxy-polyamide primer for spray
and brush applications. - Type I, Class C: Yellow - Type II,
Class C: Dark Green |
|
MIL-PRF-24635C |
Fed-STD-595C |
A high grade copolymerized silicone alkyd semigloss enamel
intended for use on primed smooth metal surfaces. It is
highly weather resistant and has superior color and gloss
retention. - Type II: 340 g/l max VOC - Type III: 240 g/l
max VOC - Class 1: Gloss - Class 2: Semigloss - Class 3: Low
gloss |
|
MIL-PRF-26915D |
Gray |
An organic type paint which produces a film containing high
metallic zinc in contact with the steel. Like galvanizing,
this zinc is electrically conductive, thereby preventing
corrosion electro-chemically. It is also suitable as a
finish coat on all ferrous and galvanized surfaces. Class A:
340 g/l max VOC Class B: 250 g/l max VOC |
|
MIL-PRF-81352B |
Fed-STD-595C |
An exterior acrylic lacquer coating for protection of metal
surfaces. |
|
MIL-PRF-85285C |
Fed-STD-595C |
A two-component aliphatic, polyester polyurethane coating. |
|
MIL-PRF-85285D |
Fed-STD-595C |
A two-component aliphatic, high solids, low-VOC, polyester
polyurethane coating. |
|
MIL-PRF-85582C |
#34151 Green #34052 Green |
A two-component waterborne epoxy polyamine primer. - Type I:
Standard #34151 Green - Type II: Low infrared reflective
#34052 Green - Class C2: Chromate rust inhibitor formulation
- Class N: Non-chromate rust inhibitor formulation |
|
MIL-PRF-85582D |
#34151 Green #34052 Green |
A two-component waterborne epoxy polyamine primer. - Type I:
Standard #34151 Green - Type II: Low infrared reflective
#34052 Green - Class C2: Chromate rust inhibitor formulation
- Class N: Non-chromate rust inhibitor formulation |
|
MIL-R-3043B |
Green (Blue in package) |
A thermosetting resin coating for surfaces of engine
components and metal parts. Dyed to a semi- transparent blue
color which changes to green upon proper baking. |
|
MIL-T-19544E |
N/A |
One type of specially blended solvent specially formulated
for the reduction of acrylic nitrocellulose lacquers. |
|
MIL-T-19588A |
N/A |
A toluene/methyl ethyl ketone mixture solvent. |
|
MIL-T-81772B |
N/A |
One type of specially blended solvent specially formulated
for the reduction of two-component polyurethane coatings. -
Type I: Polyurethane thinner - Type II: Epoxy thinner - Type
III: Lacquer and alkyd thinner |
|
MIL-V-173C |
Clear |
An air dry, moisture and fungus resistant clear gloss
varnish. Protects and insulates. |
|
MIL-V-12276D |
Green (Blue in package) |
A baking type, pigmented, semi-transparent phenolic varnish.
It is intended for use as a protective finish for lining
munitions, chemical and other containers requiring special
protection. |
|
MIL-V-13811D |
Fed-STD-595C |
An electrical ignition waterproofing varnish. |
|
MIL-V-21064A |
Fed-STD-595C |
A baking-type finishing varnish. |
|
MIL-W-5044C |
Fed-STD-595C |
A non-slip walkway coating with non-skid properties. - Type
I: Smooth, no grit - Type II: Grit added |
|
MPI #1 |
Aluminum |
An air-dry, ready-mixed aluminum coating conforming to
Federal Specifications. |
|
MPI #2 |
Fed-STD-595C |
A ready mixed, high heat coating formulated with silicone
resin to meet TPD-1000A. Will withstand solvents and normal
weather exposure. |
|
MPI #9 |
Fed-STD-595C |
An exterior alkyd gloss enamel. |
|
MPI #22 |
Aluminum |
A ready mixed, high heat coating formulated with silicone
resin. |
|
MPI #28 |
Clear |
A gloss clear, air-drying, phenolic modified, alkyd spar
varnish for use on exterior wood surfaces. It is extremely
water and mildew resistant. |
|
MPI #32 |
White Green Yellow Black Red Blue |
A ready-mixed traffic paint for application to traffic
bearing surfaces, such as Portland cement, concrete,
bituminous pavement, brick surfaces of streets, highways,
bridges, tunnels, etc. |
|
MPI #34 |
Fed-STD-595C |
A clear un-pigmented, solvent base acrylic coating
formulated specifically for use on properly prepared masonry
surfaces. |
|
MPI #49 |
Fed-STD-595C |
An interior alkyd flat paint. |
|
MPI #56 |
Clear |
An air dry, moisture resistant clear gloss polyurethane
varnish that protects and insulates. |
|
MPI #57 |
Clear |
A clear satin polyurethane coating for use on interior and
exterior wood. |
|
MPI #71 |
Clear |
A single component polyurethane coating formulated for
excellent exterior durability. This coating meets TT-C-542E
Type I / Type II, Class A. |
|
MPI #74 |
Clear |
A clear, long oil, alkyd varnish for use on interior wood
surfaces. |
|
MPI #75 |
Clear |
A clear, long oil, alkyd varnish for use on interior wood
surfaces. |
|
MPI #83 |
Fed-STD-595C |
A two-component aliphatic, polyester polyurethane coating. |
|
MPI #84 |
Clear |
A fast dryinig, solvent base nitrocellulose lacquer sanding
sealer for wood surfaces. For use on interior wood to be
topcoated with clear lacquer finishes. |
|
MPI #85 |
Clear |
A very high quality nitrocellulose lacquer with good working
properties and flow. This lacquer originally was designed as
an aircraft finishing material, but it is now specified
wherever a quality nitrocellulose finishing lacquer is
required. Available in gloss, semigloss, satin and flat
sheens. |
|
MPI #86 |
Clear |
A very high quality nitrocellulose lacquer with good working
properties and flow. This lacquer originally was designed as
an aircraft finishing material, but it is now specified
wherever a quality nitrocellulose finishing lacquer is
required. Available in gloss, semigloss, satin and flat
sheens. |
|
MPI #87 |
Clear |
A very high quality nitrocellulose lacquer with good working
properties and flow. This lacquer originally was designed as
an aircraft finishing material, but it is now specified
wherever a quality nitrocellulose finishing lacquer is
required. Available in gloss, semigloss, satin and flat
sheens. |
|
MPI #90 |
Various Stain Colors |
An interior oilbase wood stain that protects and enhances
the natural texture of fine wood. |
|
MPI #104 |
Clear |
A clear un-pigmented, solvent base acrylic coating
formulated specifically for use on properly prepared masonry
surfaces. |
|
MPI #122 |
Fed-STD-595C |
A very high quality nitrocellulose lacquer with good working
properties and flow. This lacquer originally was designed as
an aircraft finishing material, but it is now specified
wherever a quality nitrocellulose finishing lacquer is
required. Available in gloss, semigloss and satin sheens. |
|
MPI #123 |
Fed-STD-595C |
A very high quality nitrocellulose lacquer with good working
properties and flow. This lacquer originally was designed as
an aircraft finishing material, but it is now specified
wherever a quality nitrocellulose finishing lacquer is
required. Available in gloss, semigloss and satin sheens. |
|
MPI #124 |
Fed-STD-595C |
A very high quality nitrocellulose lacquer with good working
properties and flow. This lacquer originally was designed as
an aircraft finishing material, but it is now specified
wherever a quality nitrocellulose finishing lacquer is
required. Available in gloss, semigloss and satin sheens. |
|
P-415A-66 |
Green |
A two component chemically cured product that forms a film
that is resistant to chemicals, solvents, moisture,
immersion and abrasion. This product has excellent adhesion
to most substrates and is recommended for heavy duty
industrial applications where a tough, chemical resistant
primer is required. |
|
P-674-66 |
Light Gray |
A lead-free , high-solids alkyd primer for wood and ferrous
metal. |
|
T-120-66 |
N/A |
One type of thinner-reducer for pre-treatment wash primers. |
|
T-262A-66 |
N/A |
One type of specially blended solvent specially formulated
for the reduction of two-component epoxy coatings. |
|
TPD-1000A |
Aluminum |
A high-heat aluminum coating. |
|
TPD-24607 |
Fed-STD-595C |
A non-flaming coating that is resistant to burning and
flaming per ASTM E-162 with a maximum flame index of less
than 20. |
|
TT-C-542E |
Clear |
A single component clear polyurethane coating formulated for
excellent exterior durability. |
|
TT-C-2114 |
Fed-STD-595C |
An obliterating coating. |
|
TT-E-485F |
#24084 Olive Drab |
A semigloss rust inhibiting enamel for use on metal as a one
or two coat primer/finishing coating system. - Type I: Dip
application - Type II: Brush and roller application - Type
III: Roller coat application - Type IV: Flash dry
application |
|
TT-E-487E |
Fed-STD-595C |
An alkyd base floor and deck enamel for use on interior and
exterior wood and concrete floor and decks. May also be used
on ferrous metal decking subject to minimum foot traffic. It
is self priming on concrete and bare wood. |
|
TT-E-489G |
Fed-STD-595C |
A high grade, single component, air dry, high gloss alkyd
enamel formulated for interior and exterior primed metal and
wood surfaces. |
|
TT-E-489H |
Fed-STD-595C |
A high grade, high gloss alkyd enamel formulated for
interior and exterior primed metal and wood surfaces. Low
VOC, high-solids formulation. |
|
TT-E-489J |
Fed-STD-595C |
A high grade, high gloss alkyd enamel formulated for
interior and exterior primed metal and wood surfaces. A Low
VOC, high-solids formulation. |
|
TT-E-490E |
Fed-STD-595C |
A high grade silicone alkyd type copolymer gloss and medium
gloss enamels intended for use on primed metal but
particularly on smooth exterior metal. It is highly
weather-resistant and has superior color and gloss
retention. Its inherent high heat resistance is due to the
high silicone content of the resin. Resists temperatures up
to 600 degrees Fahrenheit. |
|
TT-E-496B |
Black |
A heat-resisting enamel. |
|
TT-E-506K |
Fed-STD-595C |
An interior alkyd gloss enamel. - Type I: Tints and whites -
Type II: Hi-hide white |
|
TT-E-508C |
Fed-STD-595C |
A high quality semigloss alkyd enamel for use on all wood,
metal or masonry surfaces. This product is extremely durable
with excellent flow and leveling characteristics. |
|
TT-E-509C |
Fed-STD-595C |
An odorless, interior grade, alkyd enamel formulated for low
VOC" content. - Type I: Tints and whites - Type II: Hi-hide
white " |
|
TT-E-515A |
Fed-STD-595C (Lusterless only) |
A quick-dry, lusterless, alkyd enamel formulated for low-voc
content. This coating is primarily used as a fast dry finish
coat on equipment. |
|
TT-E-516A |
Fed-STD-595C (Lusterless only) |
A quick-dry, lusterless, styrenated alkyd enamel This
coating is primarily used as a finish coat on ammunition and
other metal surfaces. |
|
TT-E-522A |
Fed-STD-595C |
An exterior phenolic enamel. |
|
TT-E-527C |
Fed-STD-595C |
An exterior grade, lusterless alkyd enamel. |
|
TT-E-527D |
Fed-STD-595C |
An exterior grade, lusterless alkyd enamel formulated for
low VOC" content. " |
|
TT-E-529G |
Fed-STD-595C |
A semi-gloss, alkyd enamel formulated for interior and
exterior metal and wood surfaces. This coating is primarily
used as a medium dry finish coat on equipment. |
|
TT-E-545C |
Fed-STD-595C |
An odorless, interior, alkyd undercoat enamel. |
|
TT-E-1384 |
Fed-STD-595C |
A durable, high gloss, acrylic enamel formulated to give
excellent exterior durability. |
|
TT-E-1593B |
Fed-STD-595C |
An air-dry, interior/exterior silicone alkyd coating for use
on primed metal surfaces. |
|
TT-E-1793 |
Fed-STD-595C |
A metal and wood furniture semigloss enamel. - Class A: Air
dry - Class B: Baking |
|
TT-E-2124B |
Fed-STD-595C |
A vinyl alkyd enamel. |
|
TT-F-1098D |
White |
A solvent-thinned block filler for porous surfaces. |
|
TT-I-735 |
N/A |
One type of alcohol that may also be called out as
Isopropanol or 2-Propanol. This solvent is 100% miscible in
water. |
|
TT-L-20A |
Fed-STD-595C |
A nitrocellulose lacquer for use primarily on metal
surfaces, usually specified by the Government for camouflage
surfaces. |
|
TT-L-26C |
Clear Fed-STD-595C |
A brushing lacquer. |
|
TT-L-32A |
Cobblestone |
A very high quality nitrocellulose lacquer with good
exterior durability and gloss. New HAPS" free formulation.
This lacquer originally was designed as an aircraft
finishing material |
|
TT-L-50E |
Clear Fed-STD-595C |
A high grade lacquer coating supplied in pressurized
dispensers for general purpose applications. - Type I:
Nitrocellulose - Type II: Acrylic - Type III:
Acrylic-cellulose acetate butyrate |
|
TT-L-50G |
Clear Fed-STD-595C |
A high grade lacquer coating supplied in pressurized
dispensers for general purpose applications. - Type I:
Nitrocellulose - Type II: Acrylic - Type III:
Acrylic-cellulose acetate butyrate |
|
TT-L-54C |
Fed-STD-595C |
An acid-resistant spraying lacquer. |
|
TT-L-58E |
Fed-STD-595C |
A very high quality nitrocellulose lacquer for general
interior use as a finishing coat over a primed metal or a
sealed wood substrate. |
|
TT-N-95B |
N/A |
An aliphatic naphtha solvent. - Type I: For organic coatings
- Type II: For cleaning acrylic plastics |
|
TT-N-97C |
N/A |
An aromatic naphtha solvent. |
|
TT-P-19D |
Fed-STD-595C |
A 100% acrylic coating that will provide excellent
durability and weather resistance. |
|
TT-P-24E |
Fed-STD-595C |
A concrete and masonry oil paint. |
|
TT-P-26C |
Fed-STD-595C |
A fire-resistant coating formulated with a special type of
alkyd resin for fire retardant coatings. This coating gives
very good fire retardancy while protecting the substrate
from abrasion and wear. |
|
TT-P-28G |
Bright Aluminum |
A ready mixed, high heat coating formulated with silicone
resin. |
|
TT-P-29J |
Fed-STD-595C |
An interior latex paint. |
|
TT-P-29K |
Fed-STD-595C |
An interior latex paint. |
|
TT-P-30E |
Fed-STD-595C (Flat only) |
An odorless interior alkyd paint. |
|
TT-P-31D |
Brown Red Oxide |
An oil paint. |
|
TT-P-32B |
Fed-STD-595C |
A blackboard coating paint. |
|
TT-P-38E |
Aluminum |
An air-dry, ready-mixed aluminum coating conforming to
Federal Specifications. |
|
TT-P-47G |
Fed-STD-595C |
A ready-mixed flat oil paint. |
|
TT-P-59E |
International Orange |
A ready-mixed paint. |
|
TT-P-81E |
Fed-STD-595C |
A high quality, long-oil alkyd enamel for use on all wood
surfaces. This product is extremely durable with excellent
flow and leveling characteristics. |
|
TT-P-85E |
White Yellow |
A ready mixed, air dry, solvent base traffic paint. |
|
TT-P-87D |
White Yellow |
A reflectorized traffic paint, premixed with low-index glass
spheres, designed for drop-on application of additional
quantity of coarser low-index spheres at time of
application; intended for traffic marking. |
|
TT-P-91D |
Fed-STD-595C |
A concrete and masonry, rubber-base, interior floor paint. -
Type I: Chlorinated rubber formulation - Type II: Styrene
butadiene formulation |
|
TT-P-95C |
Fed-STD-595C |
A chlorinated, rubber based coating designed to withstand
continuous submersion and the effects of wear and weather. |
|
TT-P-97D |
White |
A styrene-butadiene, solvent-type, exterior masonry paint. |
|
TT-P-98C |
Fed-STD-595C (Flat only) |
A flat stencil paint. |
|
TT-P-102F |
Fed-STD-595C |
An exterior grade, long oil alkyd enamel for general
exterior use on new or previously painted wood trim, siding,
primed metal and sealed concrete. It is lead and chromate
free with a low VOC" content. " |
|
TT-P-110C |
Black |
A conventional dry solvent-base traffic coating. |
|
TT-P-115F |
Red Black Blue White Yellow |
A conventional dry solvent-base traffic coating. - Type I:
Slow drying formulation - Type II: Fast drying formulation |
|
TT-P-320D |
Aluminum |
An aluminum pigment in powder or paste form for paint. -
Type I: Minimum 99% - Type II: Minimum 65% - Class A: Extra
fine lining - Class B: Standard lining - Class C: Standard
fineness |
|
TT-P-620C |
Fed-STD-595C |
A coating primer conditioner for chalking exterior masonry. |
|
TT-P-636D |
Red Oxide |
An alkyd primer coating for wood and ferrous metal. |
|
TT-P-641G |
Gray |
A two part, high-solids, zinc-dust, zinc oxide primer that
protects steel galvanically, thus preventing below film
corrosion. |
|
TT-P-645A |
Red Green Yellow |
A corrosion-inhibiting, zinc chromate primer. |
|
TT-P-645B |
Yellow |
A zinc molybdate alkyd primer |
|
TT-P-650D |
White |
A latex-base interior primer coating for gypsum wallboard. |
|
TT-P-662B |
Fed-STD-595C |
A surfacer, sanding, lacquer, and enamel type primer. |
|
TT-P-664C |
Red Oxide |
A synthetic, rust-inhibiting, lacquer resisting primer
coating. |
|
TT-P-1385 |
Gray |
A synthetic primer. |
|
TT-P-1411A |
Fed-STD-595C (Lusterless only) |
A cementitious waterproofing coating for concrete and
masonry walls. |
|
TT-P-1511B |
Fed-STD-595C |
A vinyl acrylic latex semigloss enamel with quick dry and
good adhesion. |
|
TT-P-1757A |
Green Yellow |
A low-moisture sensitivity, corrosion-inhibiting zinc
chromate primer. |
|
TT-P-1757B |
Green Yellow |
A one-component, alkyd base, corrosion-inhibiting zinc
chromate primer. |
|
TT-P-1952B |
White Yellow Red |
A conventional dry waterbase traffic coating. |
|
TT-P-1952C |
White Yellow Red |
A conventional dry waterbase traffic coating. |
|
TT-P-1952D |
Fed-STD-595C |
A conventional dry waterbase traffic coating. |
|
TT-P-2756A |
Fed-STD-595C |
A low VOC, self priming, polyurethane coating. |
|
TT-P-2846 |
Fed-STD-595C |
A recycled latex paint. - Type I: Interior - Type II:
Exterior - Type III: Interior/Exterior |
|
TT-S-171C |
Clear |
A lacquer-type floor sealer. |
|
TT-S-176E |
Clear |
A varnish-type surface sealer for wood and cork floors. |
|
TT-S-179B |
White Off White |
An oilbase pigmented wallboard and plaster surface sealer. |
|
TT-S-223B |
Clear |
A specially formulated clear acrylic based sealer designed
to be used as a sealer and dust reducer on floors. May be
used on concrete, asphalt tile, linoleum and masonry floors. |
|
TT-S-300A |
N/A |
Shellac. |
|
TT-S-711C |
Fed-STD-595C |
An interior lead free, semi-transparent stain that protects
and enhances the natural texture of fine wood. |
|
TT-S-1992 |
Fed-STD-595C |
A latex exterior wood stain. |
|
TT-T-266D |
N/A |
A thinner for cellulose-nitrate based dopes and lacquers of
the spraying type. Suitable for use under air pollution
regulations. |
|
TT-T-291F |
N/A |
Three types of Mineral Spirits (volatile petroleum spirits)
for thinning paints, enamels, varnishes and paint related
materials. |
|
TT-T-306C |
N/A |
Two types of synthetic resin enamel thinners, for general
use and limited use. - Type I: General use - Type II: Use
under air pollution restrictions |
|
TT-T-306E |
N/A |
A type of synthetic resin enamel thinner. - Type I: General
use - Type II: Use under air pollution restrictions |
|
TT-T-548F |
N/A |
Toluene. |
|
TT-T-1384 |
Fed-STD-595C |
A synthetic, gloss, acrylic enamel formulated to give
excellent exterior durability. |
|
TT-T-2935 |
N/A |
A purging thinner. |
|
TT-V-51F |
Clear |
An asphalt varnish. |
|
TT-V-81G |
Clear |
A mixing varnish for aluminum paint. - Type I: For use as
wood primer - Type II: For general use |
|
TT-V-109C |
Clear |
A clear, air-drying alkyd varnish for interior use. |
|
TT-V-119D |
Clear |
A clear, air-drying phenolic spar varnish for use on
exterior wood surfaces. It is extremely water and mildew
resistant. |
|
TT-V-121H |
Clear |
A water-resisting spar varnish. |
|
TT-W-572 |
Clear Fed-STD-595C |
A water repellent, penetrating sealer that will provide
protection to any wood or concrete surface or structure. |
|
TT-X-916B |
N/A |
One type of solvent that or thinner primarily for use in
protective coatings. |
.gif)
.gif){kind=small}